产品名称：K-508智能焊台扩展器
1、实现1主机3烙铁，方便使用，免去频繁更换烙铁头造成的损耗。
2、适用于JBC，T115、T210、T245三款型号规格的手柄，提高JBC焊台使用率，有效降低使用成本。
2、适用于JBC，T115、T210、T245三款型号规格的手柄，提高JBC焊台使用率，有效降低使用成本。
Barcode (EAN)
6922297053467
产品介绍
定制要求
增值服务
1、扩展器为JBC焊台专用，
2、试用前须用绝缘螺丝更换焊台手柄支架右侧螺丝，然后安装休眠感应连接线。
3、使用时应先启动K-508扩展器，再启动JBC主机；如先启动JBC主机，则会在拿起手柄使用时会显示“无工具”（2秒后恢复正常）可以正常升温不影响使用。
4、1#接口的手柄必须放置在主机手柄支架上。
5、1#接口和2接口可以接210或245的手柄，只须通过接口上方的手柄转换开关进行转换。
6、3#接口接JBC115烙铁手柄。
2、试用前须用绝缘螺丝更换焊台手柄支架右侧螺丝，然后安装休眠感应连接线。
3、使用时应先启动K-508扩展器，再启动JBC主机；如先启动JBC主机，则会在拿起手柄使用时会显示“无工具”（2秒后恢复正常）可以正常升温不影响使用。
4、1#接口的手柄必须放置在主机手柄支架上。
5、1#接口和2接口可以接210或245的手柄，只须通过接口上方的手柄转换开关进行转换。
6、3#接口接JBC115烙铁手柄。
1. The expander is dedicated to the JBC soldering station.
2. Before the trial, replace the screw on the right side of the soldering station handle bracket with an insulating screw, and then install the sleep induction cable.
3. When using, the K-508 extender should be started first, and then the JBC host; if the JBC host is started first, it will display "no tool" when picking up the handle to use (return to normal after 2 seconds), and it can be heated normally without affecting use.
4. The handle of the 1# interface must be placed on the host handle bracket.
5. The 1# interface and the 2 interface can be connected to the handle of 210 or 245, and only need to be converted through the handle switch above the interface.
6. The 3# interface is connected to the handle of the JBC115 soldering iron.
2. Before the trial, replace the screw on the right side of the soldering station handle bracket with an insulating screw, and then install the sleep induction cable.
3. When using, the K-508 extender should be started first, and then the JBC host; if the JBC host is started first, it will display "no tool" when picking up the handle to use (return to normal after 2 seconds), and it can be heated normally without affecting use.
4. The handle of the 1# interface must be placed on the host handle bracket.
5. The 1# interface and the 2 interface can be connected to the handle of 210 or 245, and only need to be converted through the handle switch above the interface.
6. The 3# interface is connected to the handle of the JBC115 soldering iron.